Fanuc 21i-t parameter manual

Upload aoaby. Embed Size px x x x x Warning notices are fanuc 21i-t parameter manual in this publication to emphasize that hazardous voltages, currents,temperatures, or other conditions that could cause personal injury exist in this equipment ormay be associated with its use.

Follow along with the video below to see how to install our site as a web app on your home screen. Note: This feature may not be available in some browsers. This website or its third-party tools process personal data e. To learn more, please refer to the cookie policy. In case of sale of your personal information, you may opt out by sending us an email via our Contact Us page.

Fanuc 21i-t parameter manual

Warning Warning notices are used in this publication to emphasize that hazardous voltages, currents, temperatures, or other conditions that could cause personal injury exist in this equipment or may be associated with its use. In situations where inattention could cause either personal injury or damage to equipment, a Warning notice is used. Caution Caution notices are used where equipment might be damaged if care is not taken. Note Notes merely call attention to information that is especially significant to understanding and operating the equipment. This document is based on information available at the time of its publication. While efforts have been made to be accurate, the information contained herein does not purport to cover all details or variations in hardware or software, nor to provide for every possible contingency in connection with installation, operation, or maintenance. Features may be described herein which are not present in all hardware and software systems. GE Fanuc Automation assumes no obligation of notice to holders of this document with respect to changes subsequently made. GE Fanuc Automation makes no representation or warranty, expressed, implied, or statutory with respect to, and assumes no responsibility for the accuracy, completeness, sufficiency, or usefulness of the information contained herein. No warranties of merchantability or fitness for purpose shall apply. All Rights Reserved. For details, refer to the Specifications BEN. Table 1 Related manuals.

M Distance Ls up to the ending point in inner corner override. Set the parameters to 0 forthose axes for which a load meter need not be displayed.

.

Warning notices are used in this publication to emphasize that hazardous voltages, currents, temperatures, or other conditions that could cause personal injury exist in this equipment or may be associated with its use. In situations where inattention could cause either personal injury or damage to equipment, a Warning notice is used. Notes merely call attention to information that is especially significant to understanding and operating the equipment. This document is based on information available at the time of its publication. While efforts have been made to be accurate, the information contained herein does not purport to cover all details or variations in hardware or software, nor to provide for every possible contingency in connection with installation, operation, or maintenance. Features may be described herein which are not present in all hardware and software systems. GE Fanuc Automation assumes no obligation of notice to holders of this document with respect to changes subsequently made. GE Fanuc Automation makes no representation or warranty, expressed, implied, or statutory with respect to, and assumes no responsibility for the accuracy, completeness, sufficiency, or usefulness of the information contained herein. No warranties of merchantability or fitness for purpose shall apply.

Fanuc 21i-t parameter manual

Warning notices are used in this publication to emphasize that hazardous voltages, currents, temperatures, or other conditions that could cause personal injury exist in this equipment or may be associated with its use. In situations where inattention could cause either personal injury or damage to equipment, a Warning notice is used. Notes merely call attention to information that is especially significant to understanding and operating the equipment. This document is based on information available at the time of its publication. While efforts have been made to be accurate, the information contained herein does not purport to cover all details or variations in hardware or software, nor to provide for every possible contingency in connection with installation, operation, or maintenance. Features may be described herein which are not present in all hardware and software systems. GE Fanuc Automation assumes no obligation of notice to holders of this document with respect to changes subsequently made. GE Fanuc Automation makes no representation or warranty, expressed, implied, or statutory with respect to, and assumes no responsibility for the accuracy, completeness, sufficiency, or usefulness of the information contained herein.

Marine synonym

For the parameters for the first axisthrough the fourth axis of parameter No. Type T: The gear selection signal is entered. Spindle speed command Gear 1 Gear 2 Gear 3 S command max. As many M codes as the number specified in this parameter, starting with the M code specified in parameter No. Otherwise, it is determined by the setting of parameter Very small amount of travel to be ignored. Parameter No. Division count in multiple repetitive canned cycle G73 The following show the relationship between the set values and thedrawing coordinate systems. Spindle motor minimum clamp Parameter No. When a command specifying a speed exceeding the maximum speed ofthe spindle is specified , or the speed of the spindle exceeds the maximumspeed because of the spindle speed override function, the spindle speed isclamped at the maximum speed set in the parameter. OT3x Whether stored stroke check 3 is checked for each axis is set. When a circular interpolation command G02, G03 is executed, thetolerance for the radius between the start point and the end point is set. These parameters require to assign optional software to the CNC and are automatically setdepending on the type of the software. CSD In the function for automatically reducing a feedrate at corners, 0 : Angles are used for controlling the feedrate.

.

When the function of overlapping rapid traverse blocks is enabled Fh When the function of overlapping rapid Fd traverse blocks is disabled t. G84 cannot be used as a G code for the tapping cycle; G74 cannot be used for the reverse tapping cycle. NOTE Set 0 for those position switch numbers that are not to be used. Except for special applications, the same time constant must be set for all axes in this parameter. If an F1-digit command F5 to F9 is executed, the upper limit is that set in parameter NOTE Set this parameter when using the 9. CQD The method used for determining the amount of travel in circular interpolation is: 0 : Series 16 type. NOTE 1 This parameter is valid when the multispindle control option is selected. This prevents the reference position from being set again without dogs. In either case, slave parameters are output in program format.