How to change a headlight bulb in a ford focus

The Ford Focus first sprung on the automotive scene in as a personality-laden replacement for the Ford Tempo. One of this car's calling cards is its headlight design.

Changing the dipped beam bulb on the old Mk1 Ford Focus can seem daunting, and I have read different ways of doing it. This is the way I was shown by a Ford engineer, and when you have done it once it is very quick and easy. It involves removing the headlight assembly. The main obstacle is the retaining bolt under the car! My local car hardware chain store seemed insistent that the Mk1-facelife Mk 1. The Mk1. Remove the two bolts on the headlight unit as shown in the figure using the 10 mm socket wrench.

How to change a headlight bulb in a ford focus

Log in. Sign up. JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding. Sort by Oldest first Oldest first Newest first Most reactions. I've never removed the headlights to replace bulbs on the focus. Pass side is easier, no part removal necessary. On the passenger side, remove the rubber boot from the back of the housing, and unsnap the connector from the bulb and pull it out of the way. Then the bulb and ring will just pull out. Reverse the procedure to reinstall On the driver side you may have to remove a few pieces I have an SRI, so I have to remove my air filter to get to the bulb. First time I did the whole job I almost pulled my hair out getting the attachment ring loose. Then it's wide open to the back of the headlight.

Ford Maverick.

Indeed I have read many times the advice "Take it to a dealer to get the bulbs changed", but I don't have that sort of money to throw around. Let me start by thanking Benjol for his excellent blog on changing the bulbs on the Mk1 Focus , which gave me the inspiration to try and do the same for the MK2. I hope he doesn't mind if I do this. Handling little fiddly things bulbs, screws, tools over a complicated engine with lots of deep dark holes is fraught with danger. Short of turning the car upside down and shaking it, there's not much anyone can do for you if you lose something and Murphy's law prevents it falling out the bottom.

The only tool needed to change any of the headlight bulbs in either the driver or passenger side housing is a Torx T star bit screwdriver. Locate the two screws that hold the headlight assembly in place. One screw is near the outer edge and the other is at the inner corner. Remove the two screws by turning them counter clockwise with a Torx T star bit screwdriver. Set the two screws aside in a safe place. Turn over the housing and rest it on the bumper. To avoid scratching the plastic lens or the painted bumper, place a towel in between them. Pull off the rubber dust cap on the rear of the housing to access the base of the old low beam bulb. Pry up the black plastic tab on the electrical connector before sliding it straight off the bottom of the old bulb. If you do get the new bulb dirty, wipe off the glass with an alcohol moistened paper towel.

How to change a headlight bulb in a ford focus

Headlight Size. Select year Headlight Bulb High Beam - These bulbs produce over 12, lumens of pure high-quality light!

Labcorp flemington

I found this to be the most difficult bit of the job! You may need to put down a mat to lie on, and get under the car, but once familiar you can do it by touch. Thank you very much! The weathershield has a rubber gasket which must be lined up carefully and then compressed in order for the clips to fasten. So here are a few photos to keep you happy. It is possible to remove it entirely if needed. Once the grill is loose, you should be able to lift the headlight unit away. In fact, I have not bothered to put this back in, the unit is perfectly secure on the top two bolts. The bulb is then push fitted into the holder. Use a HB2 replacement bulb for models older than and a HB5 bulb for models produced since Can you use Ford focus parts on a model? Three cheers - and so say all of us.

Log in. Sign up. JavaScript is disabled.

Carsguide is not liable for the accuracy of any information provided in the answers. Disconnect the bulb from the connector. This is the most inconvenient bit. Thanks for taking the time to document and photograph the necessary steps. The Ford Focus first sprung on the automotive scene in as a personality-laden replacement for the Ford Tempo. Sign up. This is an older thread, you may not receive a response, and could be reviving an old thread. Complete guide to Ford Focus Pull out the headlight bulb with its electrical connector straight out from the headlamp assembly. Once sat correctly, hold in place with a finger whilst closing the metal retaining loop. For a better experience, please enable JavaScript in your browser before proceeding. Refitting the headlight is the opposite process. Safely discard the old bulb. This is the most inconvenient bit.