Ipod nano 1 battery

Enter your email address below, and we will notify you when this product is back in stock. This iPod nano 1st Gen replacement battery is what you need to bring your dead iPod back to life! Battery degradation is an inevitable part of your iPod's lifespan — extend it with this new replacement battery compatible with the ipod nano 1 battery generation iPod nano.

I recently found an old iPod Nano 1st Generation that was sitting in a drawer, collecting dust since around or When it was in use, it was slightly damaged with a small dent on one side of the back. I also noticed the back was slightly coming off on the opposite side of the dent, but I assumed it was just because of the dent. Upon charging it, the opening got somewhat worse, so I unplugged it remember pin? Not only have I never really opened a piece of Apple technology this small, but I am also not really willing to remove the battery due to risk of fire or explosion. I have no replacement batteries, but this iPod is nostalgic to me and I would like to avoid throwing it away until it is absolutely necessary. Does anybody know how to safely remove the battery with the lowest risk of damage to the iPod?

Ipod nano 1 battery

The rear panel is secured to the front case by eleven clips permanently attached to the rear panel. These clips lock onto small tabs machined into the front case. To free the tabs, they must be pushed down and away from the iPod's case. Note the location of all tabs on the rear panel. When using an iPod opening tool to free the rear panel, be sure to work the tool at the location of these clips. Opening the iPod can be challenging. Don't get discouraged if it takes you a few tries before the iPod is opened. Insert the large iPod opening tool into the seam between the front case and rear panel of the iPod, below the dock connector. Run the tool back and forth to create an opening. The tool's edge should point toward the rear panel to prevent any accidental scratching of the aluminum front case.

Hold wire until solder has set. View Statistics:. Excess heat transferred to the logic board while soldering may result in electronic component damage.

.

The rear panel is secured to the front case by eleven clips permanently attached to the rear panel. These clips lock onto small tabs machined into the front case. To free the tabs, they must be pushed down and away from the iPod's case. Note the location of all tabs on the rear panel. When using an iPod opening tool to free the rear panel, be sure to work the tool at the location of these clips. Opening the iPod can be challenging.

Ipod nano 1 battery

This instructable goes over how to change the battery in your 1st Gen Ipod Nano. This ipod was found in the junk pile at instructables with a bloated battery. Next time your friend throws out their old ipod, try to fix it up! You need a bit of supplies to complete this: A Broken iPod New Battery Soldering Iron a note on batteries, you can get them off of ebay, but i got mine from iFixit. First you need to make room for the new battery, do this by desoldering the old one from the logic board. Next carefully solder the new battery onto the board, the order from the left side of the back of the ipod is: White Red Black. Lastly close the ipod back up by snapping it together and charge it! Easy right? Well not exactly, it seems that this ipod had a bit more problems than a broken battery, after charging and trying to get it to work in diagnositc mode i got the second image: a total hard drive space of

Maths genie solving equations

When using an iPod opening tool to free the rear panel, be sure to work the tool at the location of these clips. One comment. I no longer plan to use it, but I would like to keep it in a safe space with the battery fully removed and disposed of. Solder the other two battery leads in the same fashion, taking care not to bridge any of the connections together. Repair with confidence All our products meet rigorous quality standards and are backed by industry-leading guarantees. If present, remove the small piece of shrink tube protecting the new battery's positive lead. I skipped steps 8,9,, and I thought this was a bit difficult, mainly the initial separation and the soldering. Sign in. Get started with your Apple ID.

Enter your email address below, and we will notify you when this product is back in stock.

Rotate the battery out of the iPod and lay it next to the iPod. This product can expose you to chemicals including lead which is known to the State of California to cause cancer and birth defects or other reproductive harm. Insert the flat end of a spudger between the battery and the headphone jack side of the front case to pry the battery up off the adhesive securing it to the front case. Does Apple still replace old iPod batteries? I skipped steps 8,9,, and Fix Your Stuff Community Store. Shipping restrictions apply. Learn more about safe lithium-ion battery handling and proper disposal. Add a comment. The black tab will rotate up 90 degrees, releasing the ribbon cable. Lifetime Guarantee. Get started with your Apple ID. Initiate a return here.