Motion sensor urinal flush

The PIR sensor detects movement and activates the solenoid valve, allowing water into a urinal cistern.

This site requires JavaScript to function properly. Please enable JavaScript in your web browser. We offer a wide range of urinal and WC flush controls that provide optimal levels of water conservation without compromising on hygiene. The Flow Saver consists of an electronic control sensor unit and a solenoid for installation into the water supply pipe of a urinal auto cistern. The unit monitors washroom traffic to schedule cistern flushes. Where no motion is detected a hygiene flush is initiated at 12 hour intervals.

Motion sensor urinal flush

JavaScript seems to be disabled in your browser. For the best experience on our site, be sure to turn on Javascript in your browser. The Cistermiser PIR sensor detects movement within the washroom at or near the urinals and activates the solenoid valve allowing water into a urinal cistern. Pack includes the ceiling mounting kit. The use of a petcock within a urinal flushing systems has been outlawed by schedule 2, section 9, and paragraph 25 of the Water Regulations. The new and accepted solution and advice is to install an approved urinal flush control with all auto-cisterns and urinals such as the Cistermiser infrared sensor urinal flush control valve. PIR or passive Infrared urinal flush controls like the Cistermiser actually sense when a particular urinal or row of urinals is used, which is in contrast to a hydraulic valve which only senses when a washroom as a whole is used. This can provide further water savings over a standard hydraulic flush control valve and the infrared sensor Cistermiser has a hygiene cycle or janitorial flush function built in. If the sensor detects no occupancy within the washroom in 12 hour period it will automatically open the valve for 30 minutes to allow one flush of the cistern to rinse the urinals and pipe work. This reduces odours and the risk of blockages in wastes.

Download PDF. Can be calibrated to flush up to 4 times per hour but we recommend it is set to flush 20 minutes after the sensor detects a user, therefore a maximum of 3 times per hour.

This site requires JavaScript to function properly. Please enable JavaScript in your web browser. The Gentworks Flow Saver is the most popular with our online customers and offers outstanding long-term reliability and water saving. The Flow Saver consists of an electronic control sensor unit and a solenoid for installation into the water supply pipe of a urinal auto cistern. The unit monitors washroom traffic to schedule cistern flushes. Where no motion is detected a hygiene flush is initiated at 12 hour intervals.

Free returns are available for the shipping address you chose. You can return the item for any reason in new and unused condition: no shipping charges. Attach the clip of the chain to the connector of the wheel of the controller. Put the bracket on the rim of toilet tank and make sure that the wheel is right above the flapper of toilet. Stick the indicate sticker on the tank cover, try to position the sticker right above the sensor.

Motion sensor urinal flush

Batteries are included with the purchase of the toilet. The sensor will indicate when it is time to replace the batteries by blinking red when a flush is activated. Simply wave your hand within 2 inches from the sensor to activate a flush. Convenient Manual Flush Option As a backup, a manual flush button is located on the sensor for quick and convenient access if needed. Power-Off Mode for Ease of Cleaning For less hassle while cleaning the toilet, the sensor can be powered off to avoid unwanted flushes by pressing the power icon located on the sensor. Activate Touchless Flush Technology. View Products.

Beach house songs

Register Online. Please check before ordering. Ensure there is no excessive corrosion on the battery terminals. Print Page. To terminals for a V mains power supply to the integral transformer and the 6V DC output to the solenoid. The flow rate of the water into the cistern is adjustable to maximise water economy. Call us Individual Urinal Sensors with direct flush from mains water - Flushes, without cistern , immediately after use. Generally, this should be set so that the cistern fills and flushes once in every 30 minute cycle. Click here to see our brand new Autosave range which supersedes these models. Create Account. Pack includes the ceiling mounting kit. Quantity Quantity. Uncover the sensor or polish out scratches. Case Studies.

Free returns are available for the shipping address you chose.

If the sensor has been deactivated by the anti-vandal feature because the sensor has detected a presence for more than 30 minutes , then disconnect the power for 2 minutes. Catalogue Download View our product range by downloading our Specification Catalogue! If mains powered, ensure that the mains electrical power is functioning. Designed for urinals flushing directly from the mains cold water supply no cistern required. Add to basket. If no user is detected e. Solution: If a petcock or bibtap has been fitted, make sure it is removed or fully open. And now the best is even better. Things to check: Flow Regulation Solution: Decrease the flow rate by turning the flow regulator clockwise until you reach your desired flow rate. I'm really so pleased how much better my water is! This will give you access to the diaphragm note the orientation of the diaphragm when reinstalling. Is there a blockage on the outlet pipe? PIR Sensor Unit.