Titanium plasma 65

Please enter the name by which you would like to log-in and be known on this site. Please enter a password for your user account.

I was wondering if anyone has used the titanium 65 with the THC yet. Unfortunately, the divided voltage pins are and there are no raw voltage pins. This means that you will have to open the machine up and connect to raw voltage inside, since the THC requires either divided voltage or raw voltage. Thank you very much for the information. I was gonna open it up this morning and do raw voltage. I will let you all know what happens.

Titanium plasma 65

I recently ordered my very first plasma cutting table CrossFire XL and was planning on purchasing the Titanium 65 since it has the CPC port on it… However, I noticed that the Langmuir site provides a long list of plasma cutters that are not supported due to High Frequency emissions that can cause damage to the system… The Titanium is on that list… Should I stay clear of it? Also, I would like to get a machine torch set and forget and use the handheld torch without disrupting my setup. Can someone provide a part number and location where I could purchase it? The 65 only has a Plus you get a better warranty with those. By the time you buy the titanium 65 and then a machine torch for it you can buy a brand new Hypertherm powermax 45 xp for dollars more. What Richard said. I am thinking the machine torch is around for the titanium 65 and cost of machine is with tax here. Titanium 65 - not supported? Plasma Cutters General Discussion. Thanks, Melvin. Martorious February 21, , am 4.

Plasma Cutters General Discussion. This is also on the page.

.

Titanium 45 manual. This is pretty much all the manual has on it. This is its minimum setting. Everything else interpolated between these goal posts are likely proportional to these minimum and maximum figures. Maybe something like this? No dross at all. I will post some other cut 's when I get chance.

Titanium plasma 65

The Titanium Plasma 45 is a fine plasma cutter, but you should be aware of its multiple shortcomings and one major caveat. In this article, you will learn about its pros, cons, and possible alternatives, offering better features at a lower price. This lightweight, dual-voltage input plasma cutter satisfies those who need a metal-cutting solution on the go. Thanks to its build and cut quality, it can even perform when used in a professional environment. The poor duty cycle is most apparent when running on a V power supply, limiting it to thin-section cuts for only a couple of minutes. It also omits a few features expected at this price, making it overpriced. While this plasma cutter makes beautiful cuts, there are drawbacks to keep in mind. YesWelder, Everlast, Eastwood, Weldpro, and other competing brands offer better duty cycles.

Teddy bear with tuxedo

Talked to HB and they said no spare parts for at least 3 months Yes I obviously read that wrong. Can someone provide a part number and location where I could purchase it? The divided voltage is Please enter a password for your user account. I will have to contact Tecmo and Trafimet to see if its one of theirs. Thanks in advance for your insight… Melvin. TinWhisperer September 6, , pm 5. Thread Tools Show Printable Version. Cancel Changes.

I recently ordered my very first plasma cutting table CrossFire XL and was planning on purchasing the Titanium 65 since it has the CPC port on it… However, I noticed that the Langmuir site provides a long list of plasma cutters that are not supported due to High Frequency emissions that can cause damage to the system… The Titanium is on that list… Should I stay clear of it? Also, I would like to get a machine torch set and forget and use the handheld torch without disrupting my setup.

The hypertherm is a beautifully constructed machine. TinWhisperer March 5, , pm JFab September 6, , am 3. JFab , The HF in my area does not have a 65 in stock. Please type yes or no below. Well the Cutmaster is made by Esab in China need I say more. I will let you all know what happens. I'm also wondering what HF is offering that would make someone buy this unit over say a PrimeWeld Plasma Cutter in about the same price range. Results 1 to 15 of Cutting 16 ga at 25amps with a speed of 60ipm. Do you personally specify, design, recommend, or buy welding or fabricating products? The backside of 4 and 11 is where these lugs will be located. Please enter the name by which you would like to log-in and be known on this site.