Playstation 2 laser replacement

Replace the laser assembly in your optical disc drive.

Use this guide to help identify which optical laser lens replacement will fit your PlayStation 2 console. Note: Replacing the laser lens will normally require a soldering iron to remove an anti static point solder blog before install. Laser lens models can normally be identified from the console model but it is always advisable to physically remove and check the old laser prior to ordering any replacement to ensure that it is the model you expected, and that the new part is the same model or listed as a compatible replacement for the model of laser you have. Lasers will need to be fitted to the deck unit inside the console, this requires some additional rebuilding, unscrewing runners to remove the old laser and put the new one in place. This is only a few additional steps but if you are less confident with completing the repair, or you believe other parts of the laser mechanism is not working properly, you can opt to purchase the deck with the laser pre-installed. Remember the anti static solder blob will still need to be removed prior to installation or the laser will not operate, this applies to all laser units, whether attached to the deck or not. This site uses cookies to provide you with a great user experience, by using ZedLabz.

Playstation 2 laser replacement

Disconnect all cables from the console and flip the unit over to reveal its base. Locate the 6 feet on the base of the unit. Pry them off using a spudger to reveal the screws. Note: One of the feet is located under the sticker shown in the photo. Removing this sticker will void any warranty with Sony. Remove all six 4. Starting at the corner at which the power and Ethernet ports are located, pry open the outer shell using a spudger and continue around the entire unit. Note: You may use your hands for additional force to separate the two pieces of the outer shell. Take the silver rail with your tweezers and pull it towards yourself to take it out. Be carefull, as it still attached to the laser, just guide it slowly towards yourself.

This guide will explain how to replace the laser for the PS2 Slim. Starting at the corner at which the power and Ethernet ports are located, pry open the outer shell using a spudger and continue around the entire unit.

.

The screws on the right are a bit deeper inside the shell as like the rest but are the same size. Separate the clips at the front and the overhanging side from their mounting using a Prying Tool. With a plastic tool, lightly press down these two levers at the same time. Ideally, the CD should now start to spin. If it doesn't spin, the whole drive or other parts of it may be damaged and need to be replaced. Now, there are 3 flat cables to disconnect. Caution: Some have a small clamp that must first be released, so that you can carefully pull them out. Cable 2 on the other hand, has a clamp. This must be carefully preyed up from both sides before you can disconnect the cable.

Playstation 2 laser replacement

Disconnect all cables from the console and flip the unit over to reveal its base. Locate the 6 feet on the base of the unit. Pry them off using a spudger to reveal the screws. Note: One of the feet is located under the sticker shown in the photo. Removing this sticker will void any warranty with Sony.

Aslı enver spouse

Author with 1 other contributor. This site uses cookies to provide you with a great user experience, by using ZedLabz. If you maneuver the unscrewed ends of the metal rails upwards, the laser will slide out. Step 1 Top Cover. Remove all six 4. Add Comment. Replacing the laser requires you to have or purchase a new laser. It's important to remove the anti-static security, otherwise it won't work! To reassemble your device, follow these instructions in reverse order. Introduction Replace the laser assembly in your optical disc drive.

Replace the laser assembly in your optical disc drive. Replacing the laser requires you to have or purchase a new laser.

Pull the optical disc drive laser ribbon cable straight away and out of its socket. Lasers will need to be fitted to the deck unit inside the console, this requires some additional rebuilding, unscrewing runners to remove the old laser and put the new one in place. Fix Your Stuff Community Store. To reassemble your device, follow these instructions in reverse order. Open the ZIF connector. Note: One of the feet is located under the sticker shown in the photo. Number 1 Ifixit the class world,. Locate the 6 feet on the base of the unit. Step 1 Outer Shell. Almost done!